Physical Address

304 North Cardinal St.
Dorchester Center, MA 02124

How to Get Lint out of a Hairbrush

When/if I get this clean/buy a new brush I’m definitely going to compile a hygiene routine from the tips above. I think now that I haven’t been taking as much good care of it as I should be. A much cleaner brush with all the little stuff gone, but not all the lint.

Pour the solution into a wide plate and let your comb soak in this solution for about minutes. Apply this mixture gently to the bristles of your brush. This will help get rid of any debris that has accumulated onto it. If your hair is refusing to let go of the bristles, use a pair of scissors to cut down from the center.

Take the brush out of the water and then place it on a clean towel (dry towel/paper towel) to start air drying it. You can use the wide-tooth comb again to have any leftover lint removed by running it through each row of the bristles. Although, you have to have patience with this since it may take several hours to clean the lint completely. If you are in a hurry, you can use a hairdryer to speed up the process of drying it up.

In general, you should replace your hair brush every six months to one year. If you answer yes to any of the above, go ahead and replace your hair brush. You can also use your sink instead of a bowl. Broken strands of hair that fall out during brushing and end up snaking their way into a new home on your brush.

This will help any moisture drip down and onto the towel rather than back onto the handle and brush head. Use a wide-tooth comb, ideally one that isn’t too bendy. A strong comb that is metal will work best here.

My solution has always been to just pick it off with my fingernails, but my brush is different from yours – the knobs at the ends of the bristles don’t fall off. Take the natural-bristle brush out of the bowl and use your fingers or a toothbrush to scrub the spaces between the brush’s bristles. Ensure you work your way to base and use your fingers/toothbrush with the sudsy water to wash all the grim out. If there are leftover hair products in the hairbrush, you can dip them in baking soda and keep scrubbing. The baking soda will serve as an abrasive to clean out the grease/grime.

Use scissors to cut the hair stuck between the bristles into smaller pieces. This will not only make hair removal easy but also protect the bristles from separating or getting damaged. You can turn the brush bristle side down and use a toothbrush to clean lint, dust particles, and grime.

Take a clean cotton towel would be preferred, dry the combs and hair brushes with the help of the cotton towel and let the remaining water dry on its own. Keep them in some clean place so that further dirt, grime and dust particles do not stick on it as this can easily happen when the combs and hairbrushes are wet. If the handle has excessive hair product buildup, dip a toothbrush in soapy water and lightly scrub to remove any residue. Wipe the handle with a clean towel and place it on a towel with the bristles down to air-dry. I treat my brushes and combs as a separate load of laundry each week. And because I can only wash my hair every two or three days, these brushes get nas-tay with product buildup.

Leave the brush to dry, bristles facing down, on top of a clean cloth or towel. F. Now, dry the lice comb thoroughly and then soak it again in rubbing alcohol for 10 minutes. Add 1 tsp of a mild shampoo to a bowl of hot water. Add a few drops of a mild shampoo to a cup of warm water. This July the page’s simple hack for removing hairbrush buildupwent viral with over 5 million views.

“You’ll be amazed with how a simple purchase will make your hair look and feel healthier,” says Aguirre. Use your fingers or a comb to gently pull hair out of your brush. This front strands bleached way you won’t see any lint on your hairbrush. And the brush won’t pick the residue of frizzy damaged hair. You can use any of the dry cleaning methods as regular cleaning.